Sometimes also a no disc symptoms can be caused by disc table spindle platter height set too low or too high. It also indicated that they had seen other similar reports of this problem and would pass it on to the development team. If you listen closely when you put a disc in and close the tray, you should be able to hear the disc spinning up inside the player. Cleaning the inside of the player with a can of compressed air will help remove dust and dirt. Damage is more likely in a cheap, poor-quality cable. Use the small setting on the Supplemental Cache Size and click ok. Clean the travel rail and guides with a swab dampened with denatured alcohol.
Note the file name that will be listed in the description box. As to your comment on this being a 'user' forum I agree that it is but some of the users on this forum have a fairly direct line to Sony, certainly more than I do anyway. If you listen closely when you insert the disc and close the tray, you should be able to hear the disc spin up. Shake out any excess liquid from the cu-tip and then going in a circular motion, lightly clean the optical lens. On older machines it will be in the system properties and then device manager. Start Registry editor as in Step 4 b. Humphrey- Here in Kenya they are found almost in every electronics shop, for other countries i would not know.
Humphrey- Sure: if tested and found to be okay. Remember the days when all we had to do is spend a couple hours a week troubleshooting Microsoft Windows? Thank You Mar 26, 2010 Hello, The most common problem that causes a dvd player to not read discs is that the optical reading lens is dirty or the discs themselves are scratched or dirty. The causes of the problem might be one of the many that are listed below. When such problems occur, it is important to check by yourself if you have the knowledge concerning the problem. The old standby, the floppy disk drive seems to be going out of style. If it does not open and it is powered on it can be a physical issue which we will see below. You particularly need to clean the disc if you borrowed it from a library or video store.
The next common problem is that the disc is dirty or scratched. See our for more details. I clicked on the error to resolve it and it showed Superfetch auto fixing. If the belt is damaged, replace it. Composite and component connections are analog. You would simply follow the instructions on the cleaning disc and put the disc in the player and it will run through it's cleaning cycle as if the disc was a normal disc.
Then inspect the cord and on-off switch for damage and if you see any, replace them. Step Turn off player with disc inserted, unplug temporarily from wall outlet, plug back in and turn back on. Be sure that you have some technical expertise before you start off with the troubleshooting process. I recently replaced my component cables connecting my t. Enable superfetch to make boot and application speed faster. The white dots are where the relevant picture information has not been carried. After which go to the event viewer, and then click Application log.
You need a screwdriver, canned air or a soft brush, a foam swab or camera-lens cleaner, and lens cleaning fluid from a camera store. The following link to my with pictures so that you will be able to see what these and many other components look like. In the registry window, find the NoDriveTypeAutoRun entry f. All of the gear listed here--and more--is built to accept firmware updates down the road, according to Sony's support site. Save the file, then exit the Edit program.
Use circular motions to clean it, or wipe from out-to-inside or inside to out. Double-click on System icon and the Performance tab. I wish you all the best If you would not mind, please rate my help. If one device is not compliant, the other will shut down the connection. The causes of the problem might be one of the many that are listed below.
Go get a paper clip and straighten it out. You might have a scratched up dirty disk and it is unreadable by your player. When such problems occur you are likely to witness erratic problems or total failure. In this article I am going to take you through on how to troubleshoot and repair this kind of fault. It's dissapointing when they don't read the support request correctly and start asking irrelevant questions. Step one: Is the drive not showing up in Windows Explorer? If you have the technical skills or feel comfortable working on any of the items I have mentioned, it will save you a lot of money.
This is another easy and cheap fix if you have the proper tools. On the Edit menu, click Delete g. There is no need to worry since can work as a solution to such problems. I have connected them through the composite connections as I stated above in my original posting. In the right pane, right-click LowerFilters and then click Delete. The following could also cause the player to not read the disc.