The temperature can be set in 0. Programming your SmartStat thermostat for your heated flooring system is easy, just follow these steps. Can I change the programmed temperature for a short time? How do I check the programmed temperature? Display Backlight illuminates the display when a key is pressed for easier viewing in low light conditions. On cold days your Heating will be started earlier to ensure that your home is warm when you get up and on warmer days the heating system will be started later to save energy. Press and hold the Configurationbutton refer toFigure17, p.
With no other accessories fitted and for applications other than electric heating, the batteries should last about 4 years. Programming your SmartStat thermostat for your heated flooring system is easy, just follow these steps. Hook the cover over the top of the backplate. Take care to dispose of used batteries carefully. At the start of the power-up test, the thermostat screen will display the following sequence of events, in order: All icons for approximately 1. Terminal Description 8-pin Connectors Dh Dehumidify relay Hs External humidity sensor input Hp External humidity sensor power S2 External temperature sensor S1 External temperature sensor A Economizer relay Y2 Stage 2 compressor control relay W1 W2 Aux or Em heat relay b Second stage heat relay b Text in parentheses applies to only heat pump systems. Heat Cool Wake - Set to the time you wake up and the °.
Referring to Table 6, p. Waiting for a 10-minute time out after the last touch. Asistencia al cliente Llame gratis al Departamento de servicio al cliente de Honeywell al 1-800-468-1502. Press + or - to set the holiday time 1 - 99 days. Its application is the electric heating equipment and water heating system of electric heating or actuator control. Use non- flammable insulation to prevent air movement between the wall cavity and the thermostat.
Each button press will change the time by one minute. Holding the button down will change the temperature quickly. Programmable Thermostat, 1H, Conventional With Fan Option 4 Figure 8. Holding the button down will change the time quickly. How do change the batteries? WarmlyYours heated floor systems use a thermostat to maintain your chosen temperature and are easy to program. © 2016 Honeywell International Inc.
Holiday button saves energy by letting you reduce the temperature for 1 to 99 days while you are on holiday, returning to normal operation on the day you return. Remedy Check batteries are in the battery compartment and that the paper tab has been pulled out Check that the batteries have been installed in the correct orientation. Wire routing, mounting, and mounting dimensions 4. Attractive slim styling makes it ideal for location in any suitable room in your home. Holiday button saves energy by letting you reduce the temperature for 1 to 99 days while you are on holiday, returning to normal operation on the day you return.
Note: Refer toTable 3, p. Referring to Table 6, p. How do change the batteries? This warranty shall not apply if it is shown by Honeywell that the defect or malfunction was caused by damage which occurred while the product was in the possession of a consumer. Service à la clientèle Appelez le numéro gratuit du service à la clientèle de Honeywell en composant le 1-800-468-1502. Press + or - to adjust the first temperature change time. The change time can be set in 10 minute steps from 03:00 in the morning. Programmable Thermostat, 1H Only, Conventional Without Fan Option 3 Figure 7.
I am going on holiday for a few days. How do I save energy but ensure that the house is warm when I return? If an error is detected, the error code will display whereby, the user can bypass the error by pressing the Cancel icon. Push the cover thumb tab to release the cover from the backplate as shown above. Remove jumper if the 24 Vac power supplies are separate. Depending on how your thermostat was installed, the screen light may always be on.
Stylish and its mirror screen would be very easy to clean. Este activa el sistema de calefacción o refrigeración más temprano para que esté confortable a la hora que usted espera. Learn more about heated flooring systems and more at. Note: If you attempt to move a change time past the next change time, both times will be moved. Exit the System Test Modeand return to the Homescreen by: a. If the symbol does not clear itself in a few minutes call the installer Call your installer to arrange a maintenance visit.